RGM-XXS Power Factor Controller, 3P&4W(RGM-8S)

Multimeters & AnalyzersAbout RGM-6S,8S,12SRGM-6S,8S,12S reactive power control relay is designed to reduce inductive powers not used by loads but drawn from the network. If inductive reactive power is drawn from the network, it intervenes by activating capacitors of appropriate value. In this way, it tries to bring the Cos fi value to the desired level.Features7 Different Compensation Programs.Manual Compensation Option.Easy to Install and Use with 20mm. 4 Digit Led Display.Can Only Compensate Inductive Systems.Automatic Step MeasurementStep Drive, Release and Discharge Times are Adjustable.Voltage and Current Harmonic Alarm Values Adjustable.Over and Under Compensation Alarm Values Can Be Set.Voltage, Harmonic Voltage/Current, Over and Under Compensation Alarm Output.Voltage, Current and Frequency Values Can Be Monitored.Active Power, Reactive Power and Apparent Power Values Can be Monitored.Up to the 15th harmonic THD-I Can Be Monitored.Up to the 15th harmonic THD-V Can Be Monitored.Cos Value Can Be Monitored.Power Factor Value Can Be Monitored.Capacitive/Active and Inductive/Active Ratios Can Be Monitored.Automatic Fan Output.Step Values Can Be Monitored.Same Aging in Steps (In Certain \ Compensation Programs).Construction1- Step LEDs: These are the LEDs that light up when the steps are active.2- LED Display: It is the screen where all measurements, settings and notifications regarding the device are transferred to the user.3- Status LEDs: Compensation status notification LEDs.OVER: If the cos value is above the over compensation value, this LED turns on.NORMAL: If the cosine value is between the over and under compensation values, this LED will light.LOW: If the cosine value is below the undercompensation value, this LED turns on.4- Compensation Mode LED: Indicates the compensation mode of the device.5- Fan LED: It is the LED that lights up to inform the user when the fan output is active.6- Alarm LED: It is the LED that lights up to warn the user in alarm situations.7- Buttons: They are used for monitoring measurements and making settings.ESC Button: When pressed while in the menu, it returns to the upper menu without saving the values. When pressed outside the menu (on the measurement screens) it always brings up the Cosine measurement screen. When pressed for 5 seconds, Compensation Mode screen is entered.SET Button: Enters the menu/parameter. If the parameter has been changed, it will save and exit the parameter.UP Button: Scrolls through measured values outside the menu. Switches between parameters while in the menu. Increases the selected value while inside the parameters.DOWN Button: Scrolls through measured values o utside the menu. Switches between parameters while in the menu. Decreases the selected value while inside the parameters.UP + ESC Button: Step Count screen is entered when these two buttons are pressed together for 5 sec.DOWN + ESC Button: C.T. test screen is entered when these two buttons are pressed together for 5 sec.8- Measurments & Settings LEDs Indicates that the device is in the measurement or setting menu9- Value & Parameter LEDs When the device is in the measurement menu it informs that the measured value is displayed on the screen, and the parameter is displayed while in the setting menu.MaintenanceSwitch off the device and release from connections. Clean the trunk of device with a swab. Don't use any conductor or chemical might damage the device. Make sure device works after cleaning.WarningsUse the device in accordance with the instructions set by us.After the device is mounted, leave a space of at least 10 cm. behind it.Fix the device to the front cover of the panel with the accompanying apparatus.Balance the inside and outside temperature in metal panels. Otherwise, water droplets are formed on the ceiling of the panel due to the temperature difference in humid environments and this is dangerous for open connected busbars.Keep the switch and circuit breaker close to the device and within easy of the operator.Mark the switch or circuit breaker as the disconnection element of the device.Include a switch or circuit breaker in the assembly.During installation, there should be no electricity in the connection cables.Shielded and twisted cord cables should be used in input and output lines that are not connected to the network. These cables should not be passed near high power lines and devices.SpecificationsOperating Voltage(Un)..............: 100V - 300V ACOperating Frequency.................: 50/60 Hz.<;10VAOperating Temperature.............: -20°C.....+55°CStorage Temperature..................: -30°C.....+80°C<;%90 (Without condensation)Voltage Measuring Range...........:10V - 300V ACCurrent Measuring Range..........:10mA - 5,5ACurrent Transfomer Ration........:5/5A........9995/5ACos Measuring Range...............: ±0.000 ile 1.000Voltage, Current Accuracy..........:%±1Cos Accuracy..............................:%±1Active Power Accuracy................:%±2Reactive Power Accuracy...........:%±2Display............................................: 20mm. 4 Digit LED Display and Notification LEDsConnection Type..........................: Plug-in terminal connectionContacts (Step outputs).............: 3A/250V AC Resistive LoadContacts (Fan and Alarm outputs): 3A/250V AC Resistive LoadNumber of Steps..........................: RGM-6S=6 steps, RGM-8S=8 steps, RGM-12S=12 stepsCable Diameter....: 1.5mm², 2.5mm² (Voltage and C.T. connections)Weight.............................................: 500grMounting........................................:Mounting on the panel front cover<;2000metreProtection Class............................:IP41 (Front Panel), IP20 (Body)Panel Hole Sizes...........................:140mm x 140mm Set ValuesDimensionsConnection Diagram

• Multimeters & Analyzers